Aluminum saw infeed roller height is an installation handoff, not a single catalog dimension. A roller table can look level in a photograph while the stock lifts, drops or twists as its leading end reaches the saw. Before releasing a new or relocated line, compare the actual support surfaces with the machine entry, then prove that the longest and least stable profiles enter the fixture without a forced change in attitude. Record the agreed setup and an accepted first cut.
This guide is for commissioning the stock path at the saw entry. It does not assign a universal offset or claim that the pictured equipment is a supplied Jiurun configuration. The machine maker and the responsible site team must define and approve the height, alignment, guarding and trial for the exact saw, roller table and workpiece.
Aluminum saw infeed roller height: choose the contact datum
Start with the actual contact surface beneath the profile, not the top of a frame or the enclosure height. A plain roller, a crowned roller and a V-roller present different contact points. The same extrusion can also rest on a broad face, a narrow rib or a protected visible face. Mark that orientation on the drawing before anyone measures the handoff.
Identify the saw’s support or locating datum at entry and the rolling support upstream. Measure at both sides of the table and near the final roller, with the machine stationary and access controlled. A spirit level can identify twist, but it does not by itself show whether the stock meets the saw’s actual support plane. A straightedge, a representative profile and the supplier’s approved measurement method should agree.
Interroll’s roller-conveyor installation guide describes aligning adjacent module top edges with adjustable feet, checking horizontal alignment and securing the final height. That is a useful installation principle; it is not a Jiurun saw specification or a prescribed height difference for this article.

Check the whole transfer path before adjusting a foot
A locally correct reading at one roller can hide a step at a table joint, a sagging leg or a lateral mismatch at the last span. Sketch the path from the loading point through the last upstream roller to the saw’s clamp and the first outfeed support. On the sketch, mark table joints, adjustable feet, floor anchors, guides and the point where the stock becomes supported by the machine.
- Across the width: check for table twist and for a profile resting on only one edge. A narrow contact line can make a nominal level reading misleading.
- Along the length: check each transition and the final gap. A long overhang changes the way a flexible section meets the next support.
- At the fixture: confirm that the chosen orientation reaches the machine locator without being lifted or rolled by the final support.
- At discharge: make sure the accepted part is supported after separation and does not drop back into the cutting zone.
Do not silently change side guides, clamp faces or a measuring stop to compensate for a height error. Those parts establish other datums. If the table also measures or drives stock, involve the supplier and controls owner before changing its relationship to the saw. The separate guides on infeed roller load and retaining an existing roller table address capacity and ownership questions; this check is the physical release of the installed handoff.
Make the adjustment safely, then secure it
Use the machine and table manufacturers’ installation instructions and the site’s isolation procedure. Stop and isolate equipment before anyone reaches a hazardous area or adjusts supports near moving parts. Use an approved support method for the stock so a heavy bar cannot roll or fall while the table is being set. Qualified personnel should adjust the feet, check the table for twist, tighten the fasteners and secure the agreed installation before a powered trial.
Do not treat a removed guard as a convenient way to watch the transfer. OSHA’s conveyor safeguarding guidance discusses roller nip and shear hazards and the need for appropriate guarding. Apply the actual local requirements and the equipment maker’s instructions to this installation. Record any access or guarding issue as an open item before production release.
If the floor settles, a table is moved, or a support foot is reset later, repeat the relevant measurements and trial. A witness mark and dated measurement record make it easier to identify an unapproved change than a vague note that the table was “level.”
Trial the stock cases that expose the handoff
Agree the samples with the buyer before the trial. One short, rigid offcut may bridge every roller and conceal the problem. Include the longest normal incoming stock, a flexible or narrow-contact section, and the section most likely to twist or catch at entry. Use the orientation and visible-face protection required in production. State the incoming straightness condition so an existing stock defect is not mistaken for a table-height problem.
- Static presentation: with equipment stopped and under the approved safe procedure, place each sample on the upstream supports. Observe contact at the last rollers and at the saw entry. Note any daylight, rocking, forced lifting or concentrated edge contact.
- Controlled feed: with guards and controls restored, run a supervised feed using the approved method. Watch for hesitation, roll, side-guide strike or a change in stock attitude as the leading and trailing ends cross the handoff. Keep hands outside the danger area.
- First accepted parts: measure the cut length and the drawing-critical end or mating feature using the agreed inspection method. A smooth feed alone does not prove the cut is accepted.
- Repeatability: repeat with the representative mix and record any adjustment made between samples. If adjustment is needed for each profile family, make that changeover requirement explicit in the quotation and work instruction.

Write a release record that a second shift can use
A useful handoff record identifies the saw and table configuration, profile drawing and orientation, support contact points, setup method, final foot and fastener state, the person who approved guarding, the trial samples and the measured accepted parts. Photograph the final arrangement from the operator side and the table joint, but keep the numerical measurements and drawing acceptance separate from the photos. Mark any limitation, such as one profile family requiring a different guide setting.
Ask for a clear outcome: released for the named stock mix, released with a stated limitation, or not released pending correction and retest. This avoids a vague “installation complete” sign-off when the support plane has not been proven. If the saw is later moved or a roller table is replaced, this record becomes the baseline for a focused recheck. For side-datum changes, also review the infeed side-guide acceptance plan.
What the Jiurun video shows
The short video below comes from Jiurun’s own channel and shows a JR-455CNC saw and its feed area. It is related equipment context only. It does not demonstrate or certify the roller-height setting, profile mix, installed table, trial results or throughput described in this article.
Send a useful commissioning request
If aluminum saw infeed roller height is part of your commissioning scope, send the stock drawings, maximum incoming lengths, orientations, table layout, floor plan and any existing roller-table details. Ask which contact surfaces establish the proposed handoff, who adjusts and anchors each support, how the trial will be witnessed, and which cut-part measurements close the job. Jiurun can then discuss a configuration-specific trial and quotation. Contact the Jiurun team with your stock and layout.