The clamp is down and the profile has not moved, yet the machine alternates between “ready” and “not ready.” Replacing a switch at this point may leave the saw waiting for exactly the same reason. If the quoted configuration uses an aluminum saw clamp pressure switch for confirmation, the useful question is which signal first changes during a normal guarded cycle: pressure at the sensing point, the switch output, or the controller input.
This guide is a supplier and maintenance review method, not a setting recipe for a particular Jiurun machine. Some saws confirm clamp position by other means or do not expose a pressure-confirm signal at all. Obtain the actual pneumatic and electrical drawings before treating a panel message, lamp, or catalogue photograph as proof of a fitted pressure switch.

Aluminum saw clamp pressure switch: put the flicker on a timeline
Choose one released profile and an approved operating mode. Record the commanded clamp event, first jaw contact, pressure indication at the relevant circuit point, switch indication if one is fitted, controller input state, and the moment the machine grants the next motion. Keep the same material, contact face and support arrangement across repetitions. Note whether the symptom appears on every cycle, only at startup, or when another air-consuming function operates.
A regulator gauge, a switch display and a PLC status screen answer different questions. A gauge at the plant inlet may look steady while a branch nearer the clamp changes. A switch lamp describes its own output, not the mechanical grip on the extrusion. A controller status screen may update more slowly than the physical event. Ask the supplier which instrument and time base was used for each observation. If the event is too brief for a dial gauge or phone recording, a qualified technician should select an appropriate logging method under the maker’s procedure.

Three different disagreements need three different questions
Pressure and switch output both cross the boundary
If a properly located pressure record changes at the same time as the installed switch output, start with the air circuit and the actual load on it. Ask where the sensor is connected relative to the regulator, valve and cylinder. Compare the event with other simultaneous pneumatic motions and with the pressure needed by the manufacturer’s approved sequence. The observation does not, by itself, identify a leak, an undersized supply line, or an incorrect setpoint. Each remains a hypothesis until the relevant point is measured and the circuit is checked by qualified personnel.
Pressure looks steady but the switch output changes
First ask whether the pressure record has enough resolution at the switch port to support that conclusion. Then compare the actual sensor part number and configured output mode with the drawing. The supplier may need to review the ON and OFF thresholds, hysteresis, response or filtering settings, power supply, connector and wiring. Record the before-state and who is authorized to change it. Do not enlarge hysteresis merely to silence a warning: a setting that suppresses chatter can also change when the machine recognizes an inadequate clamping condition.
The switch output is steady but the control state changes
Here the pressure sensor may be doing what it was set to do. Ask the machine maker to compare the output at the device with the input observed by the controller, including the wiring path and the logic that uses that input. A display message alone cannot settle whether the cause is electrical, software-related or an intentionally timed interlock. The related clamp-release feedback guide concerns clearance before the next feed; this check concerns a fluctuating clamp-confirm condition during the hold or cut sequence.

Hysteresis is a switching rule, not proof of clamp force
A pressure switch may turn on when pressure reaches one threshold and turn off after pressure falls to a different threshold. The separation is hysteresis. The SMC ZSE10(F)/ISE10 manual describes ON and OFF points and says hysteresis can prevent output chattering. The same manual identifies output mode and response-time settings. Those are examples of component behavior, not a statement that this SMC device is installed on a Jiurun saw or that its default values apply to the machine under review.
Festo’s pressure-sensor overview likewise describes monitoring a defined pressure threshold. A pressure threshold is only one possible input to the maker’s sequence. Line pressure is not automatically a direct measure of force at the jaw: cylinder dimensions, geometry, friction, contact location and support of the profile also matter. A satisfactory switch output cannot replace observation of the actual clamping and safe machine response.
Ask for the installed sensor model and its manual before interpreting displayed units or parameters. Distinguish hysteresis from a response-time filter and from controller-side delay. If any threshold or timing is changed, the supplier should state which clamping conditions and protected motions must be revalidated. Do not bypass an input, defeat an interlock, reach into a moving saw, or intentionally create a pressure failure for an informal test.
Use a witnessed cycle to separate a signal claim from a machine claim
A useful acceptance record shows the released extrusion, clamp contact face, operating mode and machine revision. It marks the sequence in which stock is positioned, jaws close, confirmation is accepted, the cut occurs, and the clamps release. For each normal cycle, record whether the signal remains in its expected state during the documented hold interval. Compare the first cycle after a stop with repeated cycles only if the maker’s procedure allows both. Record any other air-consuming action that coincides with the flicker.
The video below is from Jiurun’s own channel and shows a different saw handling an aluminum section. It provides a view of related workholding and cutting equipment, but no pressure-switch indication, controller input trace, or test of the fault discussed here. Use it to discuss the machine area that a supplier-led demonstration should cover, then request an actual guarded sequence for the proposed configuration.
Ask for a repair or quote record that preserves the evidence
Send the supplier a short event record rather than “the sensor is bad.” Include the machine identifier and revision; the released profile drawing, finish and contact orientation; the air-supply condition; which clamp is affected; the sensor model if known; the pressure measurement location; the switch indication and controller input at the same event; and the sequence step that stops. Attach a time-stamped clip from a permitted observation point. Label any reading that was unavailable instead of filling it with an assumed value.
For a replacement proposal, ask whether the pressure switch, connection, valve, regulator or control logic is actually included, who sets it, and how the maker will document acceptance after work. A generic sensor with the same pressure range is not enough to establish electrical compatibility, output behavior, physical fit or a valid threshold. If the real problem is an air-supply disturbance, replacing only the switch may leave the event unchanged. If the problem is a controller input, changing pneumatic hardware may have no effect.
Keep this decision separate from pressure rise at idle and slow clamp release. Those articles begin with different observed events. The question here is whether a fluctuating confirmation signal follows a real pressure change, a device-output change, or a disagreement farther downstream.
For a machine inquiry, send JiurunCut your profile drawing and the observed signal sequence. Ask the supplier to identify the confirmation method on the quoted machine and show a guarded, repeatable cycle on the specified stock. Any final control or protective-function judgment belongs to the machine maker and qualified personnel working from that configuration’s documentation.