A replacement rail can be the wrong answer to a loose ski on a waxing bench. The ski may rest on an adjustable holding profile, while a separate extrusion carries the table or its legs. Both can be aluminum, but they meet different parts and need different evidence. For ski waxing bench aluminum profile cutting, locate the failed or planned interface before specifying a saw blank.
Swix’s guide to waxing tables and profiles describes ski-holding profiles used on independent legs, clamped to a table, or fitted into a dedicated table. Its T793-2 description identifies an adjustable aluminum profile and named compatible legs and clamps. Those facts describe Swix’s own system; they are not a drawing, dimension or substitution approval for another maker’s bench.
A loose ski does not identify the bad member
Start with the assembled fixture. Identify the member that touches or locates the ski, the part that attaches that member to a leg or table, and the frame that supports the work surface. A request for a “bench rail” leaves those three identities unresolved. A ski-contact support can require a protected bearing face and adjustment clearance. A frame rail may instead be controlled by a hinge, corner joint or foot. Cutting one accurately cannot repair a mismatch at another interface.
- Branded replacement support: identify the maker part number and compatible clamp or leg. The original system maker or authorized repair route confirms the replacement.
- OEM ski-contact extrusion blank: identify the released section, ski-contact face and adjustment features. The fixture design owner approves this member.
- OEM table or leg frame blank: identify the released joint, hinge or foot connection. The frame design and assembly owner approves this member.
This map is a way to separate purchase orders, not a bill of materials for a particular Swix model. If the job is a branded repair, ask for the approved replacement and compatibility information first. A retail photograph cannot prove cavity shape, alloy, wall thickness or the fit of an improvised extrusion. For an OEM design, release an end-view and assembly drawing with a distinct part number and revision for every member being cut.

Locate the interface before choosing a cut length
Suppose an OEM support is held by a table clamp. The assembly drawing should show which faces the clamp grips, which edge is exposed to the ski, and how far the profile must extend past its contact. If the support adjusts lengthwise, mark the travel area and any end feature that limits it. A stop set from the overall bench dimension could leave the support too short even when the cut length matches an old purchasing note.
The same logic changes for a table-frame member. Its datum may be a corner seat, hinge shoulder or leg connector rather than the ski-contact surface. Work backward from that approved connection to the blank’s section, orientation, end form and inspection reference. Record whether the required end is square, angled or left for secondary machining. Do not turn an assembly dimension into a saw setting without that chain of references.
Long incoming stock adds a practical check: can the proposed infeed support carry the real extrusion without changing its position at the stop or exposing a visible face to clamp damage? Bring the actual bar length, finish state and permitted contact faces to the trial. The long-extrusion handling guide covers delivery; this trial still needs a representative section and stock condition. The OEM drawing, not the article, sets the allowable variation.

Release the blank and the finished support at different gates
The first gate is the saw-cut member. Mark its identity and orientation, then inspect from the drawing’s datum. Check the cut end, burr, local shape and any face that later meets a ski, clamp or finish. If left and right pieces or paired supports are required, keep them identified through measurement and packing. A single nominal length without the mating reference is weak evidence of fit.
The second gate belongs to the fixture owner. Install the accepted blank with the actual clamp, leg, slider, hinge or table interface named by the released design. Check adjustment, attachment and ski support against that design’s criteria. A saw shop can document the cut and its setup; it cannot certify that an unfinished bar is a stable or approved waxing station. Swix’s different support arrangements illustrate why the assembled route must be specified, without establishing acceptance for this hypothetical OEM job.
If the first assembly fails, record where: the support face, adjustment travel, clamp seat, frame corner or later-machined feature. Compare the corresponding drawing and measured part before changing a saw stop. Recutting an already compliant blank will not correct an incompatible purchased clamp or an omitted secondary operation.

Only then test the proposed saw on the released member
For in-house cutting, take the approved section and member map to the machine review. Include the longest stock, the shortest and longest blanks, protected faces, expected mix and the inspection method. Watch how the quoted configuration supports and locates the actual profile, how the accepted part exits, and how a first-off measurement is recorded. Ask which supports, stops and handling accessories are included. A showroom cut of another extrusion does not establish this fixture’s fit or a production rate.
The following Jiurun Machinery channel video shows general aluminum sawing equipment. It illustrates machine motion only; it does not show a ski waxing bench member, the cited Swix product, a customer trial, a quoted configuration or measured performance.
Send the interface, not just the bench name. If the requirement is a maker-approved repair, use that maker’s replacement route. If an OEM has released an extrusion drawing, send JiurunCut the section, mating parts, stock condition and cut list for a saw-process discussion. Keep final ski-holding and bench approval with the design owner.