Opens in a new tab

MQL Lubricant Change on an Aluminum Saw: 4 Release Checks

An aluminum saw MQL lubricant change is a purchasing and release decision, not just a reservoir refill. A replacement fluid may arrive with a plausible label while the machine still contains an unknown amount of the previous product. Before production resumes, identify the exact fluid, obtain the machine supplier’s changeover instruction, and record what was actually checked on the first accepted part. This guide is for teams reviewing an MQL-equipped aluminum saw; it does not specify a lubricant or a universal purge procedure for a Jiurun machine.

Start with the two named fluids

Write down the current product and proposed replacement by manufacturer, product name, grade, and batch or container reference. If the old product is unknown, say so. Do not turn “MQL oil” into a substitute specification: different formulations and delivery components can impose different limits. The lubricant supplier should confirm suitability for the alloy, blade, downstream cleaning or bonding steps, and the intended application. The saw supplier should confirm compatibility with the actual reservoir, seals, lines, metering device, and nozzle arrangement. Ask both parties whether residual old fluid can remain and what evidence supports their answer.

MQL is commonly described as a system that uses a small, fresh supply of lubricant rather than recirculating a flood coolant. That distinction matters when planning a change, but it does not prove that two products can be mixed. The UNIST MQL Handbook explains the delivery principle; it is general industry guidance, not a fluid approval for this saw.

Separate an approved changeover from a top-up

A top-up adds fluid to a known, approved system. A changeover replaces the product and needs a boundary between old and new material. Ask for a written, machine-specific sequence that identifies who isolates the equipment, which components are drained or cleaned, whether lines require purging, how the new product is introduced, and how waste is handled under the site’s rules. The exact steps must come from the equipment and lubricant suppliers and the site’s competent staff. Do not infer them from a photograph or from another manufacturer’s manual.

For perspective, Haas’s MQL service guidance includes a purge after a fluid change on its own equipment. That is evidence that the fluid boundary can matter; it is not a Jiurun procedure or permission to copy the Haas steps. If a supplier says no purge is needed on the quoted saw, request that conclusion in writing for the named old and new fluids and the actual installed system.

Technician measuring an aluminum extrusion sample; illustrative MQL lubricant change release check
Related inspection illustration: a technician measures an aluminum profile. This is not a sample from the lubricant change described here.

MQL lubricant change: what the release record must show

An MQL lubricant change cannot be released from the container label alone. One signed sheet is more useful than an undocumented “fluid changed” note. Give the maintenance and production teams a common record with the following fields:

  • Product identity: old and new lubricant names, grades, containers, dates, and the supplier approval for this machine and material.
  • Changeover authorization: the machine-specific instruction and the person who completed it, including any approved drain, clean, or purge record.
  • Delivery observation: the observed liquid delivery at the relevant point under the approved setup, with any abnormal result escalated. Air movement alone does not establish lubricant delivery; see our separate MQL flow check.
  • First accepted part: the representative profile, blade and program identifiers, cut-face and dimensional checks, and the reviewer who released production. Record what was measured; do not invent a universal acceptance limit.

A low-level alarm or refill event belongs in a different record. It may prompt a response, but it does not by itself show that a new product is compatible or the changeover is complete. Our lubricant-level warning guide addresses that separate trigger.

Aluminum workpieces arranged on a table for surface review
Related aluminum sample review scene only. These pieces are not claimed to be saw-cut parts, a fluid-change trial, or evidence of performance.

What the equipment video shows

The following video from Jiurun’s own channel shows an automatic aluminum cutting machine operating. It provides equipment context only. The footage does not demonstrate the lubricant product, MQL configuration, changeover steps, first-part result, or compatibility of any fluid discussed above.

Before approving a replacement lubricant

Ask the saw supplier and lubricant supplier to review the exact old product, proposed new product, installed MQL components, aluminum profile, blade, and downstream process. Request their written compatibility decision and the machine-specific changeover instruction. Then agree on the first-part inspection and who signs the release. If any of those inputs are unknown, keep the approval conditional until they are established. A general product brochure, machine video, or clean-looking cut face cannot close the gap.

For a Jiurun equipment inquiry, send the machine model and serial or quotation reference, photos of the installed lubrication components, both lubricant product sheets, and a representative profile drawing. Jiurun can review the equipment side of the question against the actual configuration; the lubricant manufacturer should confirm its product’s material and application limits. Contact Jiurun with those records before treating the replacement as released.

ALUMINUM CUTTING MACHINE QUOTE

Which Machine Fits?
What Will It Cost?

Tell us what you need to cut. We’ll confirm the details with you, recommend a machine and prepare a quote.

  • A machine for your partsWe review your aluminum material, size and cutting needs.
  • Machine proposal and pricingSee the recommended machine, included equipment and price.
  • Help with your cutting problemDiscuss burrs, material waste, slow cutting or too much manual work.
Want to check the cut before ordering?Ask about a sample-cutting test for your material.
Start with just 2 detailsYour WhatsApp / phone number + email address.
No model or drawing needed to get started.

Prefer to chat?

Chat on WhatsApp

Send Your Inquiry

WhatsApp / phone and email are required. Your name or company, cutting details and drawings are optional.

JiurunCut | Global Inquiry
Include + and your country code. A regular phone number is fine.
Share any details you know: material or alloy; profile shape, size and wall thickness; cut length and angle; required precision; daily output; automation needs; and current cutting problems. We will use these details to recommend a suitable machine configuration, cutting process and quote. You can add drawings or photos below.
No drawing ready? You can send it later.
We’ll use your details to respond to your inquiry. Privacy Policy